H
How much power does a 5906/5907 receiver card draw
The receiver cards draw 0.44W max.For 5V input that's 0.88AFor 12V input that's 0.037AFor 24V input that's 0.018A
...
How much dry ice does an Aquafog 3300 hold?
You can put up to 100lbs of dry ice in a Aquafog 3300 tray. ...
How many Lumens does the QolorFLEX Pixel tape output
The QolorFLEX pixel tape outputs 350 lumen ...
How do I set a 2.4 SHoW ID on my Multiverse Show Baby?
You will need a DMXCat or an RDM capable device in order to set a 2.4 SHoW ID on any Multiverse Show Baby.
...
How long can my DMX extension cable be from my QolorPix Controller to QolorPix tape?
The max cable length is 25'. ...
How do I change my 5942 dimmer back to wired input mode without loosing any configuration changes?
Remove power from the dimmer, press and hold bump buttons B and D, while applying power. Wait for all lights to flash, the status light ...
Heating Elements no longer heating up
If everything on the control panel seems to be working correctly, then it is possible that the heating elements may be burned out. If ...
How do I check the health of my QolorPoint Battery?
o Open Fixture and remove the battery
o Disconnect all wires from the battery
o Use a multimeter to test voltage
o Is voltage 24v or higher?
▪ Yes, ...
How do I set a static IP address in my Multiverse Transmitter?
Via the DMXCat app connect to your Multiverse Transmitter. Once you are connected please follow the following steps: 1. Select the purple Multiverse Transmitter button ...
How many candle can be powered from the AC Adapter?
The AC Adapter can only provide 200mA of power @ 9 Volts, so it can only power one candle. ...
How long will the bulbs in my flame tips last?
The average life of the lamps in the flame tips is one year of normal use when used with the standard 7.5V City Theatrical AC ...
How are City Theatrical’s present candles different from the ones they sold in previous years?
We have made a number of improvements in our candles. We made the candle stick slightly larger in diameter (1.375” vs. 1”) to enable ...
How many candles are supported on a P/N3481 AC Adapter for Six Candles?
45 LED candles and 6 incandescent candles can be supported. ...
How is the Candle Kit wired to a 9v battery?
A “battery snap” is needed and is obtainable from Radio Shack, any hobby shop or any electronics supply such as Digi-Key (www.digikey.com) or Allied Electronics ...
How is the Candle Stick connected to a 9v battery?
Open the battery door on the bottom of the candle and pull out the built in battery snap. Attach the battery snap to a ...
How do I know which hardware revision I have in my MV Studio?
In the menu of your studio go to the Firmware Info page and this will list all Firmware and Hardware information on the device available ...
How do I find fixtures in the DMXCat 6000 fixture database?
DMXCat App > Connect to Dongle > Fixture Controller > Database > Top right corner magnifying glass > Type in desired fixture or search > ...
How to on how to connect Luminaire to the Multiverse Transmitter 5910, 5911, 5912?
1) Turn on Multiverse Transmitter2) Connect to Multiverse Transmitter with DMXCat app on device3) Go to RDM Controller4) Press the RDM arrow on the Multiverse ...
How do I set an internal scene PDS-750?
1. Turn on the unit2. Go to Advanced Setup in the Main Menu Screen; Press Enter 3. Input setup; Press Enter4. Enter and Arrow up ...
How do I set an Internal Scene on a PDS-375?
1. Turn on the unit2. Go to Advanced Setup in the Main Menu Screen; Press Enter 3. Input setup; Press Enter4. Enter and Arrow up ...
How do I know what firmware I am running on my 5902/5903 Node?
On the Multiverse Node, go to the menu and find the information screen. You will see a list of all firmware versions. Below is an ...
How do I turn on the relay in my ColorSource Relay?
• Auto Mode: Relay turns on when DMX/ RDM input is detected. Relay turns off five minutes after data is last detected. (Default Mode)• DMX ...
How do I wire the +, A-E for the LED Tape to my 5942/5943?
The wires in A-E can vary but the one consistent is: + - Black cable Typical wiring is + - Black A - Red B ...
How long can the lead be from the dimmer to the LED Tape?
It can be as long as you need it to be but you will need to consider voltage drop over long distances. This will vary ...
How do I set stand alone light output with on the 5821/5823/5825 dimmer?
You will need to set the dimmer to Run 2 mode and power cycle the device. Once you have done that you will need to ...
How long can I extend the antenna for my wireless DMX system and is it RG-58 cable?
No it is not RG-58 cable. The impedance of the cable needs to be 50ohm. Typically LMR-200 and LMR-400 and its equivalents are used.The length ...
How much Dry Ice will I need?
50 lbs. of Dry Ice will produce about 10 minutes of fog.
...
How long will a fresh 9v battery last with my Candle Kit or Candle Stick?
About two hours for the regular incandescent bulb candles.
...
How long does the LED candle kit last on a 9V battery?
The LED bulbs last up to 20 hours per battery, but are not quite as realistic looking asour standard incandescent bulbs.
...
How long is the 2199 Power Supply cable?
The 2199 Power supply cable is a little over 3' long. The DMX cable is only 1' long.
...
Heater error light comes on after a minute or two even after replacing the problem heater.
Test the PCBA in the test fixture to see if the problem continues. If it does not follow the PCBA, you will need to replace ...
How do I connect my MV Transmitter 5910/5911/5912 to my Chamsys Console?
We found the biggest issue was that the console recognizes ART-Net Universe 0 and we do not. I found that you can change this in ...
How can I charge the battery on my QolorPoint 7000?
The charging case PN 7015 and the bottom charge port The front port with Single Unit Power Supply PN 7024
...
How do I change the function of my QolorPoint 7000?
To change Function press FN. Use the up and down buttons to select “CHANGE Function” and press enter to accept.Then use the up and down ...
How can I tell if my QolorPoint 7000 is charging while in my Charging Case 7015?
The Power LED will turn Red and change to Orange then Green once fully charged. Be sure to only charge the units with the Charging ...
How far can my QolorPoint 7000 be from my transmitter?
Distance to transmitter (outdoors, and depending on conditions)• Less than 1,500ft. for SHoW Baby or Multiverse TransmitterDistance between Master unit and Slave unit• Less than ...
How do I factory reset my Node?
Hold the up and down arrows at the same time. The text on the screen will flash and reset to factory settings.
...
How do I set DMX Mode in my 5825?
Power on the deviceArrow up or down till you see Run2 Press enterArrow up or down till you see Run1 Press SelectPower cycle the unit
...
How do I set a SHoW Key on my Node?
This can be down at the device itself or via RDM. On Device: Menu settingsShow Key - This can be any number between 0 - ...
How do I install and setup my 2192 DMX Iris?
Installation and Setup1. On the Source 4, remove the 2 screws holding the patternholder slot cover and remove the cover and set it aside.2. Insert ...
How do I setup my COlorSource Relay with the 5903 Node
Follow the Users manual that is provided with the product.
...
How many watts does the 5916/5917 draw?
These 5916/17 Dimmers draw 0.36W in wireless mode and 0.27W in wired mode.
...